Introduction
This manual also covers ClassBuddy™ branded wall units.
Decide on a suitable location for your ChargeLite™ Wall to be mounted.
The unit must be fixed to a solid wall or directly to studs, if the unit is being fitted to a non-solid wall. The use of hollow wall or plaster board type fixings are not recommended. Allow space above and below the
wall unit for ventilation.
Ensure that you check the wall prior to any drilling and fixing for electrical cables or other services that may be in the wall/void. Make sure the unit is at an acceptable user height. We recommend installing the ChargeLite Wall between a height of 800-1200mm to ensure the locker bays are available at accessible heights for your end users.
Select suitable fixings for the wall that you are fixing to and ensure that you use a minimum of 9 of the possible 16 fixing positions available (Ensuring as even distribution as possible).
IMPORTANT Two people are required to carry out the installation.
Product Weight: 28kg
Tools Required
- Corded or cordless power drill (hammer-action required for solid walls)
- Drill-bit to suit your fixing type (refer to manufacturer’s instructions)
- Pencil/Pen (to mark hole positions)
- Spirit level
- Hammer
- Screwdriver/Impact Driver
- Vacuum cleaner
Fixings Required (solid wall)
- 9 Screws 7.5mm x 60mm long
- 9 Wall Plugs 10mm x 50 mm long
Product Weight: 28kg
Installation Process
-
Stand Up
- Once unpacked, stand the unit up and ensure you have a clear working space around all sides.
-
Open doors
-
Open the left hand side door with the white key, and the right hand side door with the black key.
-
-
Unscrew holding nuts
On the bottom right hand side of the unit, there are two holding nuts that need to be unscrewed, these can be unscrewed by hand.
-
Once you have done this, lock the doors back up.
Holding Nuts
-
-
Unhook Mounting Bracket
Unhook the mounting bracket by titling the ChargeLite™ Wall forward and pushing the mounting bracket down.
-
Level the Mounting Bracket
Hold the mounting bracket up against the wall with the bottom lip facing towards you.
Use a spirit level to make sure the bracket is level on the wall and ensure the hanging slots are at the top.
You may need two people for this.
-
Mark Drill Holes
Use the pencil or marker to mark all the fixing holes, then remove the mounting bracket.
-
Drill Holes
Drill holes for fixings in accordance with the manufacturer's instructions.
The following instructions are for brick walls only.
- Ensure an even distribution of fixings.
-
Use a minimum of 9 fixings
-
Secure Mounting Bracket
Place the mounting bracket back onto the wall with the bottom lip facing towards you, and screw your fixings into place in accordance with the manufacturer’s instructions.
-
Hook the Wall Unit
Once the mounting bracket is secured lift the ChargeLite™ Wall into place.
There are six hooks along the sides that the unit slides onto.
Two people are required to lift the ChargeLite™ Wall.
Ensure that ChargeLite™ Wall is hooked on correctly and that the three lower studs are through the fixing holes before gently releasing the unit. -
Secure
Once in place, open both doors again (Step 2) and screw the two holding nuts in onto the studs that you removed in Step 3.
Complete
Your new ChargeLite™ Wall should now be successfully installed onto your wall and you are ready to load your cables and devices.
Please refer to the user guide that is supplied with your ChargeLite™ Wall for further information.
Please read the Health and Safety guidance in the User Manual.
If you have any problems please do not hesitate to contact our support team.
Useful Links
|
Support Enquiries: |
|
|
Warranties:
Warranty Activation: www.lapsafe.com/activate
Warranty Details: www.lapsafe.com/warranty
|
|
|
Replacement Keys:
|
LapSafe® Self-Service Solutions Ltd
3 Wakes Hall Business Centre,
Wakes Colne, Colchester, Essex;
CO6 2DY